Transformer Manufacturing Machine-Double wire crawler traction paper wrapping machine

Transformer Manufacturing Machine-Double wire crawler traction paper wrapping machine-SPL- power transformer, distribution transformer, oil immersed transformer, dry type transformer, cast coil transformer, ground mounted transformer, resin insulated transformer, oil cooled transformer, substation transformer, switchgear

Double wire crawler traction paper wrapping machine

Have been tested by us for 7 years to be the most cost-effectirve among different modles of Double wire crawler traction paper wrapping machines. We can help you to derease the risk of transformer manufacturing equipment selection, especially for a new transformer factory.

Descriptions

1. Machine name: double wire crawler traction paper wrapping machine.

2. Operation method: When the operator stands on the front of the machine: 1. Feed in with the right hand and discharge with the left hand, that is, pay off the wire on the right hand side and take up the wire on the left hand side. 2. The material is fed by the left hand, and the material is discharged by the right hand, that is, the wire is unwound on the left hand side and the wire is taken up on the right hand side.

3. Feeding wire specification:

Width: 2.5-14mm Thickness: 1-5mm

Cross-sectional area: 5-60mm2.

4. Specifications of insulating paper:

Thickness: 0.05—0.075mm

Width: 10-30mm

5. Wrapping requirements:

5.1 Taping direction: when wrapping a single wire, one wrapping head rotates in one direction, and the other wrapping head can wrap in the opposite direction or in the same direction.

5.2 Wrapping method: seam wrapping; overlapping wrapping: the range is 0-65%. Pitch drift ≤±0.2mm.

6. Pay-off: (according to customer requirements)

6.1 There are 2 sets of pay-off frames.

6.2 Pay-off frame type: belt pulley. Belt damping pay-off, manual lifting disc

7. Straightening device: 2 sets

7.1 The number of guide wheels on each plane: 5 horizontal and 5 vertical.

7.2 Guide wheel diameter: 30mm

8. Single wire wrapping head: 2 sets

8.1 Quantity of dust cover: each set of wrapping heads has a protective cover with soft lighting inside.

8.2 The number of single wire wrapping heads in the same dust cover: 2, one of the wrapping heads can be reversed, and the other can be turned forward, reversed and stopped.

8.3 The position of each wire wrapping head: horizontal

8.4 Paper tray diameter: outer diameter 280mm, inner diameter 75mm

8.5 The number of paper trays on each wrapping head: 2 pieces, up to 2 sheets of paper can be wrapped.

8.6 Tray clamping method: locknut

8.7 Tray position: 2 on the same plane, 4 pieces in total

8.8 There is a pressure plate at the entrance and exit of each wrapping head, which compresses the wire to prevent the wire from jumping during normal operation.

8.9 Adjustment of wrapping tightness: the damping band hand nut can be adjusted.

8.10 Winding Angle Adjustment: Guide Rod

8.11 Pair seam wrapping spacing: ≤±0.2mm Overlapping wrapping range: 0-65%

8.12 Self-locking seam wrapping: Yes

8.13 Paper break principle: mechanical paper break switch

8.14 When the paper breaks suddenly at the maximum line speed, the wire moving distance: S≤200mm

8.15 Number of paper break switches on each wrapping head: each tray has a paper break switch

8.16 Material of all guide wheels in contact with paper: stainless steel or nylon

8.17 linkage rod: easy to move

8.18 Power transmission: each group of wrapping heads is driven by synchronous belt

8.19 Rated speed of wrapping head: 550RPM for two-layer wrapping.

9. Traction device: 2 sets