site logo

  • 28
  • Feb

Peralatan manufaktur trafo-Garis pemotongan lembaran baja silikon (2 potong-3 pukulan)

Peralatan manufaktur trafo-Garis pemotongan lembaran baja silikon (2 potong-3 pukulan)-SPL- power transformer,electrical transformer,Combined compact substation,Metalclad AC Enclosed Switchgear,Low Voltage Switchgear,Indoor AC Metal Clad Intermediate Switchgear,Non-encapsulated Dry-type Power Transformer,Unwrapped coil dry-type transformer,Epoxy resin cast silicon steel sheet dry-type transformer,Epoxy resin cast amorphous alloy dry-type transformer,Amorphous alloy oil-immersed power transformer,Silicon steel sheet oil-immersed power,electric transformer,Distribution Transformer,voltage transformer,step-down transformer,reducing transformer,low-loss power transformer,loss power transformer,Oil-type Transformer,Oil Distribution Transformer,Transformer-Oil-lmmersed,Oil Transformer,Oil Immersed Transformer,three phase oil immersed power transformer,oil filled electrical transformer,Sealed amorphous alloy power transformer,Dry Type Transformer,dry Transformer,Cast Resin Dry Type Transformer,dry-type transformer,resin-casting type transformer,resinated dry type transformer,CRDT,Unwrapped coil power transformer,three phase dry Transformer,articulated unit substation,AS,Modular substation,transformer substation,electric substation,Power Sub-station,Preinstalled substation,YBM,prefabricated substation,Distribution Substation,compact substation,MV power stations,LV power stations,HV power stations,Switchgear Cabinet,MV Switchgear Cabinet,LV Switchgear Cabinet,HV Switchgear Cabinet,pull-out switch cabinet,Ac metal closed ring network switchgear,Indoor metal armored central switchgear,Box-type substation,custom transformers,customized transformers,Metal enclosed electrical switchgear,LV Switchgear Cabinet,

Transformer Manufaktur peralatan– Garis nglereni lembaran baja silikon
(2 potong-3 pukulan)

 

Dites dening kita kanggo 6 taun dadi paling biaya-effectirve antarane modles saka Silicon steel sheet slitting garis. Kita bisa mbantu sampeyan nyuda resiko trafo Manufaktur pilihan peralatan, utamané kanggo pabrik trafo anyar.

Keterangan

1. Requirements kanggo bahan coil digunakake ing baris produksi iki:

Toleransi jembaré: ≤0.1mm

Ketebalan: ≤0.03mm

S degree deviasi: ing 1000mm, siji arah ora luwih saka 0.1mm

Gelar gelombang: ≤15mm / 1000mm (span ora kurang saka 1000mm, lan dhuwur ora ngluwihi 15mm)

2. Range pangolahan:

Ketebalan lembaran: 0.18 ~ 0.35 mm Lembar

Jembar: 40mm ~ 400mm

Dawane film: 400 ~ 2500mm

diameteripun punching: 10mm ~ 24mm

Posisi punching: offset rong arah ing garis tengah

V punch eccentricity (sadawane tengah sheet): 30mm

3. Presisi: Toleransi dawa: 0.2mm / 1m

Toleransi Sudut: 0.1 ° Gunting gunting: ≤0.02mm (500,000 kali / saben ngasah sapisan)

Punching burr: ≤0.02mm (200,000 kanggo 300,000 kaping / saben sharpening sapisan)

4. Slicing kacepetan: bab 60 irisan / min

5. Total kapasitas diinstal: bab 24KW

6. Total konsumsi udara: 1.5m³/min (tekanan sumber udara: ora kurang saka 0.6MPa)

7. Tegangan operasi:

(1) Fluktuasi tegangan 380V10%

(2) Frekuensi 50HZ±2%

8. kahanan lingkungan: Suhu ora luwih saka 45C; Kelembapan ora luwih saka 85%

9. Arah operasi Piranti arah operasi: kiwa